- 重点词汇
- ofprep. 关于;属于…的;由…制成;
- camshaftn.凸轮轴;
- controlledadj.受约束的，克制的;
- aart. (用于可数名词或单数名词前，表示未曾提到的)一(人、事、物);用于前有形容词或后有短语的不可数名词前;一（个）;每一（个）;任一（个）;
- theart.这个;指已提到或易领会到的人或事物;指独一无二的、正常的或不言而喻的人或事物;用以泛指;与形容词连用，指事物或统称的人;用于姓氏的复数形式前，指家庭或夫妇;（指特定用途的事物）足够，恰好;每，一;当前的，本，此;（重读，表示所指的为知名或重要的人或事物）
- valven.阀;真空管;（管乐器的）活栓;（心脏的）瓣膜;
- isvt.& vi. 是(be的三单形式);
- openingn.开幕，开始;空缺的职位;[商]开盘，交易开始时间;（职位的）空缺;
- byprep. 在…旁边;表示方式;由于;经过;到…之前;
- 相关例句
These engines are known as dual overhead camshaft ( DOHC ) engines.
这些发动机被称为双顶置凸轮轴 ( DOHC ) 发动机.
网络文摘精选
Since 1958, an engine with a single overhead camshaft has been used.
从1958年起, 便已使用带有单顶置凸轮机的发动机.
词典精选例句
Remove the camshaft retaining bolt and remove the sprockets and chain as an assembly.
拆去凸轮轴固定螺栓,并拆去作为一个总成的链轮和链条.
网络文摘精选
This means that the crankshaft will make two revolutions for every revolution of the camshaft.
这意味着凸轮轴每旋转一次曲轴将旋转两次.
网络文摘精选
Argon arc remelting hardening is a new technology of manufacturing camshaft.
氩弧重熔硬化是生产凸轮轴新工艺.
网络文摘精选
Upward camshaft; chain transmission; timing gas distribution system is stable and has little noise.
顶置凸轮, 链条传动, 正时配气系统传动平稳,噪音小.
网络文摘精选
In this paper, the theory of cam profiling by CNC swing type camshaft grinder is analyzed.
详细分析了摇架式凸轮轴磨床凸轮轮廓的数控成形原理.
网络文摘精选
A camshaft driven by a chain or belt turns in the same direction as the crankshaft.
凸轮轴被链或者带驱动,使其朝着曲轴相同的方向转动.
网络文摘精选
The camshaft and crankshaft gears can be connected directly, or meshed.
凸轮轴和曲轴齿轮可能被直接连结, 或者相啮合.
网络文摘精选
Two TDC ( Top Dead Center ) sensors are mounted at the rear of the single camshaft.
两个上死点的传感器安装在凸轮轴的后面.
网络文摘精选
A formula of the camshaft rotating velocity is deduced while keeping constant metal removal rate.
推导出了保持磨除率基本恒定时,数控凸轮轴磨床磨削凸轮时凸轮轴转速变化的计算公式.
网络文摘精选
The isothermal quenching process of the ductile iron camshaft was analyzed.
对球铁凸轮轴的等温淬火工艺进行了分析.
网络文摘精选
The front timing cover and and a finished camshaft with timing gear on the end.
前面的时间和范围,并完成与凸轮轴齿轮的时间就结束.
网络文摘精选
试验了孕育剂量对凸轮轴组织和性能的影响.
网络文摘精选
As camshaft rotates, the lobe, or high spot of the cam, pushes of the valve.
当凸轮轴旋转时, 凸轮凸起的或者高点的位置, 推动气门座.
网络文摘精选
The metal shaft, called the camshaft, typically has individual cams for each valve in the engine.
那金属轴叫凸轮轴, 在发动机里的每个气门一般有各自的凸轮.
网络文摘精选
